How do you attach a dollfie dream head to a 40 cm obitsu/paradox body?

Are you supposed to get a neck adapter? Or do you need a mdd internal frame? Or something like that? I'm confused...

What you'll see below are photos of an Obitsu 50 neck joint + DDH-10. To my knowledge, the neck joint for the Parabox 40cm is identical to the Obitsu 50.

First, take the neck joint itself and disassemble it.

The part marked with a red "X" is a part you won't use.

Now reassemble and attach the neck joint as shown in the photos below.

 

I would add a plastic washer of some kind between that spring and the head because over time the spring WILL cause cracks and can push thru that hole damaging it.  I only say that because it's happened to me several times so now I use plastic washers under all of the ones I have and there have been no issues since.

 

 

Billy

On 8/17/2019 at 9:00 PM, growcian said:

What you'll see below are photos of an Obitsu 50 neck joint + DDH-10. To my knowledge, the neck joint for the Parabox 40cm is identical to the Obitsu 50.

First, take the neck joint itself and disassemble it.

The part marked with a red "X" is a part you won't use.

Now reassemble and attach the neck joint as shown in the photos below.

 

Thank you so much for these very demonstrative intructions! I had a problem with fitting my Dollce head(Myau) on a obitsu 40cm(parabox) body:D With your instructions, I got the head attached and working well🙏🙏🙏

Ohhhh that's a nice technique. I actually attached my DDH head to obitsu 50 body by cutting two loops off the spring and using the neck connector as it is intended. It works too

This is really helpfull as I was looking To put a DD head on an Obitsu body in the near future!

Banjo here is a DD #10 head on a obitsu 40cm. I plan on switching this head to the 45cm body soon.

Just checking, but I assume using a washer instead of the triangular piece gives me more range of motion?  (From the person who just put on a head while using the triangular piece lol)

Thanks for this guide! I had no trouble attaching a Dollce head to an O48-type body and used a plastic washer that came with my O24 as Billy suggested above.

Interestingly, mimiwoo has a similar guide for this process, but they have you not remove the cap. I imagine it would be quite difficult to get it on with that cap's extra length though.

Edited November 20, 2021 by chef_mai

On 8/19/2019 at 1:04 AM, baldylox said:

I would add a plastic washer of some kind between that spring and the head because over time the spring WILL cause cracks and can push thru that hole damaging it.  I only say that because it's happened to me several times so now I use plastic washers under all of the ones I have and there have been no issues since.

 

 

Billy

Hi i plan on buying from amazon plastic washer do you know what size should i buy?

7 hours ago, Greta said:

Hi i plan on buying from amazon plastic washer do you know what size should i buy?

I actually use white plastic body washers for radio controlled cars for mine.  😄 

Like these:  Amazon.com: Hobbypark RC Body Washers for 1/10 Scale Traxxas Redcat Arrma Axial Losi HPI HSP RC Cars Trucks Buggy Body Shell Mount Replacement, Replace 1815 (Set of 25) : Toys & Games

 

 

Billy

On 1/13/2023 at 12:47 AM, baldylox said:

I actually use white plastic body washers for radio controlled cars for mine.  😄 

Like these:  Amazon.com: Hobbypark RC Body Washers for 1/10 Scale Traxxas Redcat Arrma Axial Losi HPI HSP RC Cars Trucks Buggy Body Shell Mount Replacement, Replace 1815 (Set of 25) : Toys & Games

 

 

Billy

Thank you so much!