Screw and Nut size

Was changing the bust size on one of the girls. And i heard something fell and hit the ground. Now I am missing the inner frame screws and bolts that hold the upper torso internal frame.

So does anyone know the size of them. I am guessing they are metric and UNF (Unified National Fine Thread).

 

Thank you for your help

35 minutes ago, HK47 said:

So does anyone know the size of them. I am guessing they are metric and UNF (Unified National Fine Thread).

 

Which ones? There are a lot of upper frame screws. 

sorry the part on the inner lower frame that tightens on the shaft for the upper frame

 

 

Im guessing its smaller than a M2  but there is a lot if i remember to M0

Edited March 1, 2023 by HK47

Judging by a ruler (my digital calipers are unavailable at the moment) they are either M1, or M1.2 x 6mm

the german branch of amazon seems to have mini screw sets around the 9€ range that also include M1 screws, the trouble is those sets seem to only have nuts in M1.2 size, and M1 sized would need to be bought separate. also need to keep an eye on the screw lenghts included in the sets.

 

9 hours ago, HK47 said:

sorry the part on the inner lower frame that tightens on the shaft for the upper frame

Was the frame inside the doll when the screw came loose? Could any of the missing components be inside one of the other parts, or did you hear them both go skittering across the floor?

They were in the frame and when I turned it upside down to get them out. They fell and skidded across the floor.

 

I'm just exhausted from working too much and not sleeping.

 

I should of never change her bust when i was that tired.

15 hours ago, HK47 said:

I should have never change her bust when i was that tired.

Normally the screws shouldn't fall out like that, but on f3 they do need periodic tightening. 
 

I lost something very tiny off a doll recently, and the only reason I found it was that I sent my Roomba off to hunt for it. XD

By devils luck I found one of the bolts. By the looks of it I'm guessing it is a M1.5 or a M1.6.

On 3/3/2023 at 9:10 PM, HK47 said:

By devils luck I found one of the bolts. By the looks of it I'm guessing it is a M1.5 or a M1.6.

Is this also for the washer too? English isn’t my first language so I do apologize.

 

I also lost the screw and washed for the same internal frame part and can’t seem to find it in my room. Luckily I found the screw, but the washer..having no luck. 
 

12 hours ago, Matcha said:

Is this also for the washer too? English isn’t my first language so I do apologize.

 

I also lost the screw and washed for the same internal frame part and can’t seem to find it in my room. Luckily I found the screw, but the washer..having no luck. 
 

For washers you need to know the inner diameter and the outer. Easiest is to locate another one on the frame, and take measurements there. Then go to a hardware store (or Amazon).

There is no washer . And the part was Adjustment of fuselage joints.

https://dollfie.volks.co.jp/dd/support/basebody/howto_ddf3_dd.html

#9 is what I had to fix 

On 5/27/2024 at 9:38 PM, HK47 said:

There is no washer . And the part was Adjustment of fuselage joints.

https://dollfie.volks.co.jp/dd/support/basebody/howto_ddf3_dd.html

#9 is what I had to fix 

Yeah, I meant to say the nut size.

 

I ordered a set of these to see which would fit, since other hardware stores I went to doesn't have the correct size for the little guy.